Docker latent worker

class buildbot.worker.docker.DockerLatentWorker

Docker is an open-source project that automates the deployment of applications inside software containers. Using the Docker latent worker, an attempt is made at instantiating a fresh image upon each build, assuring consistency of the environment between builds. Each image will be discarded once the worker finished processing the build queue (i.e. becomes idle). See build_wait_timeout to change this behavior.

This document will guide you through the setup of such workers.

Docker Installation

An easy way to try Docker is through installation of dedicated Virtual machines. Two of them stands out:

Beside, it is always possible to install Docker next to the buildmaster. Beware that in this case, overall performance will depend on how many builds the computer where you have your buildmaster can handle as everything will happen on the same one.

Note

It is not necessary to install Docker in the same environment as your master as we will make use to the Docker API through docker-py. More in master setup.

CoreOS

CoreOS is targeted at building infrastructure and distributed systems. In order to get the latent worker working with CoreOS, it is necessary to expose the docker socket outside of the Virtual Machine. If you installed it via Vagrant, it is also necessary to uncomment the following line in your config.rb file:

$expose_docker_tcp=2375

The following command should allow you to confirm that your Docker socket is now available via the network:

docker -H tcp://127.0.0.1:2375 ps

boot2docker

boot2docker is one of the fastest ways to boot to Docker. As it is meant to be used from outside of the Virtual Machine, the socket is already exposed. Please follow the installation instructions on how to find the address of your socket.

Image Creation

Our build master will need the name of an image to perform its builds. Each time a new build will be requested, the same base image will be used again and again, actually discarding the result of the previous build. If you need some persistant storage between builds, you can use Volumes.

Each Docker image has a single purpose. Our worker image will be running a buildbot worker.

Docker uses Dockerfiles to describe the steps necessary to build an image. The following example will build a minimal worker. Don't forget to add your dependencies in there to get a succesfull build !

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
FROM debian:stable
RUN apt-get update && apt-get install -y \
   python-dev \
   python-pip
RUN pip install buildbot-worker
RUN groupadd -r buildbot && useradd -r -g buildbot buildbot
RUN mkdir /worker && chown buildbot:buildbot /worker
# Install your build-dependencies here ...
USER buildbot
WORKDIR /worker
RUN buildbot-worker create-worker . <master-hostname> <workername> <workerpassword>
ENTRYPOINT ["/usr/local/bin/buildbot-worker"]
CMD ["start", "--nodaemon"]

On line 11, the hostname for your master instance, as well as the worker name and password is setup. Don't forget to replace those values with some valid ones for your project.

It is a good practice to set the ENTRYPOINT to the worker executable, and the CMD to ["start", "--nodaemon"]. This way, no parameter will be required when starting the image.

When your Dockerfile is ready, you can build your first image using the following command (replace myworkername with a relevant name for your case):

docker build -t myworkername - < Dockerfile

Reuse same image for different workers

Previous simple example hardcodes the worker name into the dockerfile, which will not work if you want to share your docker image between workers.

You can find in buildbot source code in master/contrib/docker two example configurations:

worker
the base worker configuration, including a custom buildbot.tac, which takes environment variables into account for setting the correct worker name, and connect to the correct master.
pythonnode_worker
a worker with Python and node installed, which demonstrate how to reuse the base worker to create variations of build environments.

The master setups several environment variables before starting the workers:

BUILDMASTER
The address of the master the worker shall connect to
BUILDMASTER_PORT
The port of the master's worker 'pb' protocol.
WORKERNAME
The name the worker should use to connect to master
WORKERPASS
The password the worker should use to connect to master

Master Setup

We will rely on docker-py to connect our master with docker. Now is the time to install it in your master environment.

Before adding the worker to your master configuration, it is possible to validate the previous steps by starting the newly created image interactively. To do this, enter the following lines in a Python prompt where docker-py is installed:

>>> import docker
>>> docker_socket = 'tcp://localhost:2375'
>>> client = docker.client.Client(base_url=docker_socket)
>>> worker_image = 'my_project_worker'
>>> container = client.create_container(worker_image)
>>> client.start(container['Id'])
>>> # Optionally examine the logs of the master
>>> client.stop(container['Id'])
>>> client.wait(container['Id'])
0

It is now time to add the new worker to the master configuration under workers.

The following example will add a Docker latent worker for docker running at the following adress: tcp://localhost:2375, the worker name will be docker, its password: password, and the base image name will be my_project_worker:

from buildbot.plugins import worker
c['workers'] = [
    worker.DockerLatentWorker('docker', 'password',
                              docker_host='tcp://localhost:2375',
                              image='my_project_worker')
]

In addition to the arguments available for any Latent Workers, DockerLatentWorker will accept the following extra ones:

docker_host
(mandatory) This is the adress the master will use to connect with a running Docker instance.
image
(optional if dockerfile is given) This is the name of the image that will be started by the build master. It should start a worker. This option can be a renderable, like Interpolate, so that it generates from the build request properties.
command
(optional) This will override the command setup during image creation.
volumes
(optional) See Setting up Volumes
dockerfile

(optional if image is given) This is the content of the Dockerfile that will be used to build the specified image if the image is not found by Docker. It should be a multiline string.

Note

In case image and dockerfile are given, no attempt is made to compare the image with the content of the Dockerfile parameter if the image is found.

version
(optional, default to the highest version known by docker-py) This will indicates wich API version must be used to communicate with Docker.
tls
(optional) This allow to use TLS when connecting with the Docker socket. This should be a docker.tls.TLSConfig object. See docker-py's own documentation for more details on how to initialise this object.
followStartupLogs
(optional, defaults to false) This transfers docker container's log inside master logs during worker startup (before connection). This can be useful to debug worker startup. e.g network issues, etc.
masterFQDN
(optional, defaults to socket.getfqdn()) Address of the master the worker should connect to. Use if you master machine does not have proper fqdn. This value is passed to the docker image via environment variable BUILDMASTER
hostconfig
(optional) Extra host configuration parameters passed as a dictionary used to create HostConfig object. See docker-py's HostConfig documentation for all the supported options.

Setting up Volumes

The volume parameter allows to share directory between containers, or between a container and the host system. Refer to Docker documentation for more information about Volumes.

The format of that variable has to be an array of string. Each string specify a volume in the following format: volumename:bindname. The volume name has to be appended with :ro if the volume should be mounted read-only.

Note

This is the same format as when specifying volumes on the command line for docker's own -v option.